Build on Category II with machine dynamics, resonance testing, ODS, modal analysis, advanced bearing analysis and program leadership.
Registered students receive access to the Mobius Learning Zone for pre-study, course videos and post-course review.
Use advanced spectra, waveforms, phase and cross-channel measurements to diagnose difficult faults.
Test natural frequencies and resonance using run-up/coast-down, impact, ODS and modal techniques.
Correct resonance problems, set alarms and lead a successful vibration program.
Filters, order tracking, cross-channel measurements, correlation, coherence and advanced analyzer settings.
Collect and interpret time waveforms and phase data to diagnose difficult machinery conditions.
Understand natural frequencies, resonance, mass, stiffness, damping and SDOF/MDOF behaviour.
Use run-up/coast-down, impact tests, ODS, modal analysis and introductory FEA concepts.
Analyse rolling-element and journal bearings, motors, gears, pumps, fans and compressors.
Correct resonance, review balancing and alignment, set alarms and run a successful vibration program.
• Senior vibration analysts
• Condition monitoring specialists
• Reliability and rotating-equipment engineers
• Vibration team leaders and supervisors
• Analysts progressing to Category III certification
• Consultants responsible for complex diagnosis
Training requirements are aligned with ISO 18436-2.
MIBoC certification is accredited to ISO/IEC 17024.
VCAT III certification is valid for five years.
Attend a scheduled Mobius Institute VCAT III course with other participants.
Bring the Mobius Institute VCAT III course to your site and train your team together.
Complete the Mobius Institute VCAT III course online at your own pace using the pre-recorded training option.
Choose either a place on a scheduled instructor-led Mobius Institute VCAT III public course or complete the Mobius Institute VCAT III course online through the pre-recorded training option.
Includes course materials, access to the Mobius Learning Zone and the MIBoC certification exam.
A self-funded rate is available for individuals personally covering the cost of their training. Contact Elite Reliability before booking for details.
Book the Mobius Institute VCAT III course using secure Stripe checkout.
After payment, your public course date or online training option will be confirmed. For online training, the delivery address for your course materials will also be confirmed.
For private on-site training, group bookings or other delivery arrangements, contact Elite Reliability.
Signal processing: low-pass, band-pass, high-pass and band-stop filters
Sampling, aliasing, dynamic range and signal-to-noise ratio
Resolution, Fmax, data-collection time, averaging, windowing and leakage
Order tracking, cross-channel measurements, correlation and coherence
Time waveform analysis: correct setup, collection and fault diagnosis
Phase analysis: data collection, bubble diagrams and diagnostic use
Machine dynamics: natural frequencies, resonance, mass, stiffness and damping
Single-degree and multi-degree-of-freedom systems
Run-up and coast-down testing, Bode plots and Nyquist plots
Impact testing and bump tests
Operating Deflection Shape (ODS) analysis and Motion Amplification
Modal analysis and introduction to Finite Element Analysis (FEA)
Correcting resonance using mass, stiffness, damping, isolation and tuned absorbers
Rolling-element bearing fault detection and high-frequency techniques
Journal bearing analysis: displacement, orbits, centerline diagrams, oil whirl and oil whip
Electric motor fault detection and motor-current analysis
Pump, fan and compressor fault diagnosis
Gearbox fault detection using spectra, time waveforms and supporting wear-debris information
Corrective action: maintenance repair, balancing and shaft alignment
Running a successful condition monitoring program: baselines, alarms, goals and reporting
Review of relevant ISO standards
See sections of the instructional videos and a chapter from the VCAT III manual.
View the Mobius Institute vibration brochure for additional course and certification information.
Yes. The course is open regardless of experience. All attendees receive a certificate of completion. ISO Category III certification requires the exam, the required practical experience and previous VCAT II certification through a MIBoC-approved certification body.
Thirty-six months of practical vibration analysis work experience is required and must be verified by a supervisor or manager. Previous VCAT II certification through a MIBoC-approved certification body is also required.
Yes. Registered students receive Learning Zone access with digital course materials and course videos. For public instructor-led courses, access supports pre-study and review and continues for four months after course completion. For online distance learning, access is provided for four months from registration and payment.
Vibration analysis certification is valid for five years.
